Maytag Washer/Dryer Combo Parts

Dryer thermal fuse located on the blower housing. If the dryer overheats, the thermal fuse blows cutting off power to the motor or the heating system. When the fuse is bad the dryer won't start or will run but not heat. The thermal fuse cannot be reset. Fuses often blow due to a clogged dryer vent.

OEM Part - Manufacturer #WP3392519

A bad fuse will have no continuity meaning the electrical path is broken. A multimeter can be used to test it for continuity.

Dryer gas burner valve solenoid set. If the dryer does not heat or heats intermittently the coils could be defective. To test, watch the burner and if the igniter glows for a while and then shuts off without the gas igniting, it usually means one of these coils is bad.

OEM Part - Manufacturer #279834

Washer drive motor coupler. New style with metal sleeves for added strength. This version replaces all previous motor coupler styles and versions. For direct drive washing machines. Common symptom of failed coupler is washer will fill, not agitate or spin but will drain the water from the tub.

OEM Part - Manufacturer #285753A

Helpful tool is the suggested Multi-Bit Screwdriver

Dryer drum support roller kit. Includes two washers. When the drum rollers are worn out, they can cause the dryer to make a loud rumbling noise. Both rollers should be replaced at the same time. The roller does not need lubrication, the bearing is self lubricanting.

OEM Part - Manufacturer #12001541

Dryer drum support roller. If the dryer is making a rumbling or knocking noise the rollers may be worn out causing the drum not to turn smoothly.

OEM Part - Manufacturer #WPW10314173

Dryer tri-ring retainer for drum support rollers.

OEM Part - Manufacturer #WPW10512946

Dryer drum drive belt, 93 1/2 inches long, 4 ribs 3 grooves. The drive belt is a very long, slender belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley. If the drum will not turn when the dryer is turned on the belt is likely broken.

OEM Part - Manufacturer #661570V

Dryer lint filter. Air flow is vital to proper dryer operation. The lint filter should be cleaned before every load and replaced if damaged.

OEM Part - Manufacturer #W10120998

Dryer cycling thermostat with internal bias heater, L155-25. If the dryer won't heat, it is unlikely that this thermostat is causing the issue, as the thermal fuse or thermal cut-out normally fail first.

OEM Part - Manufacturer #WP3387134

Dryer drum roller axle. If the dryer is noisy this roller axle or the roller itself may be worn and require replacement.

OEM Part - Manufacturer #WP6-3129480

Dryer drum drive belt, 100 inches long, 3/8" wide,5 ribs 4 grooves. The drive belt wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley. If the drum will not turn when the dryer is turned on the belt is likely broken.

OEM Part - Manufacturer #WPY312959

Make sure the belt is aligned on the high part of the drum. If it is riding in the groove it will rub on the idler pulley guide arm.

Affresh™ Washing machine cleaner. This cleaner removes and prevents odor-causing residue in all brands of washers. To use, add one tablet to washer with no clothes and select hot water.

- Septic safe
- More effective than bleach.
- Three tablets per package.

OEM Part - Manufacturer #W10135699

Affresh® Dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up.

Dryer igniter kit. This igniter will replace both round and flat style igniters. The kit includes the bracket, wire nuts and mounting screw. Be aware the igniter is very fragile and should be handled carefully.

OEM Part - Manufacturer #279311

Consider replacing the gas valve coils while you have the dryer apart.

Dryer idler pulley. The idler pulley puts tension on the drive belt. If the idler pulley fails to put the proper amount of tension on the belt, the dryer will not spin.

OEM Part - Manufacturer #279640

The dryer belt wears out over time. Consider replacing the belt while the dryer is apart.

Washing machine clutch assembly with hardware. *Blue spring for large capacity washers, black for compacts. A worn clutch often causes a slower spin speed which leaves the clothes soaked after the cycle.

OEM Part - Manufacturer #285785

Dryer door catch kit. This kit includes three different door catches; you will need to select the door catch that fits your model.

OEM Part - Manufacturer #279570

Dryer thermistor. This thermistor should read approximately 11.9K Ohms of resistance at 70 degrees Fahrenheit (21’ Celsius). If the thermistor is defective, it may prolong or shorten the drying time or cause a fault code. A defective thermistor is not responsible for a dryer not heating.

OEM Part - Manufacturer #WP8577274

Washing machine suspension spring. If the suspension spring is broken, the washer will be off balance.

OEM Part - Manufacturer #WP63907

Dryer drive belt. The belt has a length of 91 5/8” and width 5/16”. The belt has 5 ridges. If the dryer drum won’t rotate, but the motor is running then the belt has likely broken.

OEM Part - Manufacturer #WP33002535

While the dryer is apart consider replacing the idler pulley when installing a new belt.

Dryer front drum support glide. Order 2 when repairing the dryer. Be aware it requires a rivet tool to install the new glide and the tool must be purchased locally.

OEM Part - Manufacturer #306508

Consider replacing the drum support rollers while you have the dryer apart as they wear out over time.

Heating element thermal cut-off (thermal fuse) 360 degrees and high-limit thermostat 250 degrees. The thermal fuse is a safety device designed to protect the dryer from overheating. A multimeter can be used to test the fuse. Always check the dryer venting when replacing a blown thermal fuse.

OEM Part - Manufacturer #279769

The fuse can be tested using a multimeter meter

Idler pulley wheel and bearing. If the idler pulley wheel and/or bearing is defective, it may cause the dryer to be excessively noisy.

OEM Part - Manufacturer #WP6-3700340

Dryer high limit thermostat and thermal fuse kit. If the dryer does not heat the most common cause is a blown thermal fuse. Both the thermostat and fuse can be tested to determine if either is defective.

OEM Part - Manufacturer #279973

Dryer igniter with wire harness connecter. This is a flat-style igniter. The igniter uses heat to ignite the gas in the burner assembly. If the igniter is defective, the gas will not ignite and the dryer will not heat.

OEM Part - Manufacturer #4391996

Washing machine drain pump. *Coin trap only available with pump assembly. If the washer does not drain the pump could be locked up or a small object may be clogging it. Also a small leak in front of the washer could be caused by a defective pump.

OEM Part - Manufacturer #WPW10730972

If your washer smells we recommend cleaning it with Affresh once a month.

Washing machine tub counterbalance spring. This spring offsets the weight of the motor on the front of the washer. If broke, the tub will lean forward and the tub will be off balance during the spin cycle.

OEM Part - Manufacturer #WPW10250667

White silicone adhesive caulk

OEM Part - Manufacturer #W10841140

Screw

OEM Part - Manufacturer #WP308685

Gas dryer sensor for igniter and flame. The sensor is located across from the gas igniter at the dryer’s burner assembly. This flame sensor should be closed for continuity at room temperature. Check for continuity with a multi-meter before replacing.

OEM Part - Manufacturer #WP338906

Dryer lint filter. This filter should be cleaned before every load to ensure proper airflow for dryer operation. If the lint filter is ripped or torn, replace it.

OEM Part - Manufacturer #WP33001808

Washer belt kit for Maytag models. If the washer does not agitate, spin, or drain then one of the belts could be worn and require replacement.

OEM Part - Manufacturer #12112425

Light bulb, 10 watt.

OEM Part - Manufacturer #WP22002263

Dryer blower wheel for exhaust with clamp. If the dryer does not heat properly then this wheel may be stripped causing an air flow problem.

OEM Part - Manufacturer #Y303836

Adjustable leveling leg for washing machine. This leveling leg has a rubber foot. If the leveling leg is not adjusted properly, the washer will be off-balance and will vibrate or shake during operation.

OEM Part - Manufacturer #WPW10001130

Dryer moisture sensor bar. This moisture sensor monitors the clothing’s moisture level and sends a signal to the control board when the clothes are dry. If your moisture sensor is defective, the dryer may shut off too early or continue running for a while after the clothes are dry. Two required.

OEM Part - Manufacturer #WP3387223

Washer agitator bolt with rubber gasket and thread sealant. Head is 7/16 inches in diameter.

OEM Part - Manufacturer #WP358237

Timer dial skirt

OEM Part - Manufacturer #WP33001621

Order a new knob base and cap to get all the parts for the timer knob assembly.

Cleaning brush for refrigerators, freezers, dryers and more. This brush is perfect for cleaning condenser coils on refrigeration systems. It is important to regularly clean the condenser coil to ensure the refrigerator is running efficiently.

OEM Part - Manufacturer #4210463RW

Pair this tool with this vacuum extension tube and easily clean under appliances without having to move them.

Shock absorber. This shock absorber prevents the washer from vibrating by absorbing the movements of the washer tub.

OEM Part - Manufacturer #W10822553

High temperature adhesive for installing rubber and felt seals, 2 ounces.

OEM Part - Manufacturer #WPY055980

Snap retaining ring

OEM Part - Manufacturer #WP9703438

Dryer slide in lint filter (lint trap). Proper air flow is critical to dryer operation so the filter should be cleaned before every load. Replace the filter if it has any tears or rips in it.

OEM Part - Manufacturer #WP33001003

White touch-up paint

OEM Part - Manufacturer #72017

Dryer drum drive motor. Includes pulley for dryer drum drive belt. Other shaft has reverse threads for blower wheel. Common symptoms of a bad drive motor are:
-Dryer stops turning during cycle
-Dryer won't start
-Dryer won't turn at all
-Dryer drive motor is loud

OEM Part - Manufacturer #279827

Washing machine agitator repair kit. Includes agitator cam and 4 directional cogs (also called dog ears). If the upper section of the agitator isn't turning properly, then the agitator cam and dog ears are likely worn-out and require replacement.

OEM Part - Manufacturer #285751

To purchase the dog ears separately, order item 3109.

Washing machine main tub seal

OEM Part - Manufacturer #W10814296

Dryer blower wheel retaining ring.

OEM Part - Manufacturer #WP25-7855

Washer drive block for inner tub. A worn drive block may cause the washer to spin slowly, causing the clothes to be soaked at the end of the cycle. The washer may also make a loud knocking noise at the beginning of the spin cycle.

OEM Part - Manufacturer #WP389140

Washing machine tub suspension pads (package of 3). These pads help to absorb the movement of the washer tub. If a tub pad is worn, the washing machine will be unbalanced and will vibrate or shake during the spin cycle.

OEM Part - Manufacturer #285744