Refine Selection Here:
Item # 3479
This part fits your Washer/Dryer Combo
Dryer gas burner valve solenoid set. If the dryer does not heat or heats intermittently the coils could be defective. To test, watch the burner and if the igniter glows for a while and then shuts off without the gas igniting, it usually means one of these coils is bad.
OEM Part - Manufacturer #279834
Item # 400518
This part fits your Washer/Dryer Combo
Dryer drum support roller kit. Includes two washers. When the drum rollers are worn out, they can cause the dryer to make a loud rumbling noise. Both rollers should be replaced at the same time. The roller does not need lubrication, the bearing is self-lubricating.
OEM Part - Manufacturer #12001541
Item # 1246110
This part fits your Washer/Dryer Combo
Dryer drum drive belt, 100 inches long, 3/8" wide,5 ribs 4 grooves. The drive belt wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley. If the drum will not turn when the dryer is turned on the belt is likely broken.
OEM Part - Manufacturer #WPY312959
Item # 1245880
This part fits your Washer/Dryer Combo
Dryer blower wheel for exhaust with clamp. If the dryer does not heat properly then this wheel may be stripped causing an air flow problem.
OEM Part - Manufacturer #Y303836
Item # 1309
This part fits your Washer/Dryer Combo
Dryer front drum support glide. Order 2 when repairing the dryer. Be aware it requires a rivet tool to install the new glide and the tool must be purchased locally.
OEM Part - Manufacturer #306508
Item # 1480353
This part fits your Washer/Dryer Combo
Dryer drum roller axle. If the dryer is noisy this roller axle or the roller itself may be worn and require replacement.
OEM Part - Manufacturer #WP6-3129480
Item # 3452
This part fits your Washer/Dryer Combo
Dryer slide in lint filter (lint trap). Proper air flow is critical to dryer operation so the filter should be cleaned before every load. Replace the filter if it has any tears or rips in it.
OEM Part - Manufacturer #WP33001003
Item # 402507
This part fits your Washer/Dryer Combo
Washer belt kit for Maytag models. If the washer does not agitate, spin, or drain then one of the belts could be worn and require replacement. Belt sizes: 41 in x 5/16 in, 42-1/3in by 7/16 in
OEM Part - Manufacturer #12112425
Item # 1243096
This part fits your Washer/Dryer Combo
High temperature adhesive for installing rubber feet and felt seals, 2 ounces.
OEM Part - Manufacturer #WPY055980
Item # 4369899
This part fits your Washer/Dryer Combo
White silicone adhesive caulk. Forms a heat resistant bond. Often used for gaskets, seals and burner grate feet.
OEM Part - Manufacturer #W10841140
Item # 3018
This part fits your Washer/Dryer Combo
Dryer igniter with wire harness connecter. This is a flat-style igniter. The igniter uses heat to ignite the gas in the burner assembly. If the igniter is defective, the gas will not ignite and the dryer will not heat.
OEM Part - Manufacturer #4391996
Item # 1480349
This part fits your Washer/Dryer Combo
Dryer idley pulley. The idler pulley puts tension on the drive belt. If the idler pulley fails to put the proper amount of tension on the belt, the dryer will not spin.
OEM Part - Manufacturer #WP6-3037050
Item # 2681
This part fits your Washer/Dryer Combo
Gas dryer sensor for igniter and flame. The sensor is located across from the gas igniter at the dryer’s burner assembly. This flame sensor should be closed for continuity at room temperature. Check for continuity with a multi-meter before replacing.
OEM Part - Manufacturer #WP338906
Item # 3472
This part fits your Washer/Dryer Combo
Dryer door catch kit. Includes door catch and clip (plastic)
OEM Part - Manufacturer #306436
Item # 1378530
This part fits your Washer/Dryer Combo
Three terminal door switch kit. Be aware that this switch replaces older 2 terminal switches.
OEM Part - Manufacturer #W10169313